$84.19 Buy It Now or Best Offer
free,30-Day Returns
Seller Store
() %,
Location: Ontario, California, United States
Ships to: US,
Item: 274737575652
eBay Introduction: Our store provide varieties of High Quality Suspension Products, if this iterm can not meet your needs, you can entry our store to find the products you need. Before you place the order, please check the compatibility and the view Notes or contact us, make sure it fits your vehicle. we hope you enjoy your shopping. Fit for 2001 – 2004 FORD ESCAPE All Models 2001 – 2004 MAZDA TRIBUTE All Models Package Includes: 1x Front Lower (Passenger Side) Control Arm Assembly – K80397 1x Front Lower (Driver Side) Control Arm Assembly – K80398 2x Stabilizer / Sway Bar End Link – K80104 4PCS Front Lower Control Arm Stabilizer Sway Bar Link For 2001-2004 Ford Escape Introduction: Our store provide varieties of High Quality Suspension Products, if this iterm can not meet your needs, you can entry our store to find the products you need. Before you place the order, please check the compatibility and the view Notes or contact us, make sure it fits your vehicle. we hope you enjoy your shopping. Fit for 2001 – 2004 FORD ESCAPE All Models 2001 – 2004 MAZDA TRIBUTE All Models Package Includes: 1x Front Lower (Passenger Side) Control Arm Assembly – K80397 1x Front Lower (Driver Side) Control Arm Assembly – K80398 2x Stabilizer / Sway Bar End Link – K80104 10 Year Warranty Please check above compatibility list to make sure it fits your vehicle. Note: Some of the parts we have grease fittings and other parts come factory sealed, you may receive one of the parts.but don’t worry, this does not affect the performance or quality of the parts. Suspension Control Arm Some lateral multilink front suspensions have compression and lateral lower arms. The lateral arm prevents front wheel movement, and the compression arm prevents fore-and-aft front wheel movement. A rubber insulating bushing in the inner end of the lateral arm is bolted to the chassis. A second rubber insulating bushing near the outer end of the lateral arm is bolted to the damper fork. The upper end of the damper fork is bolted to the front strut. A ball joint in the outer end of the lateral arm is bolted into the steering knuckle. A rubber insulating bushing in the inner end of the compression arm is bolted to the chassis, and a ball joint in the outer end of this arm is bolted into the steering knuckle. The upper control arm is mounted higher so it is above the front tire. The higher upper control arm and the lateral and compression lower arms provide excellent suspension stability and steering control, especially during high-speed cornering or when driving on irregular road surfaces. A ball joint in the outer end of the upper control arm is attached to the top of the knuckle, and two shafts in the inner end of this arm are bolted into the strut tower. There are no provisions for camber or caster adjustments on this multilink front suspension. Suspension Control Arm Replacement Guideline: Control arms are installed in pairs on the front and rear axle and connect the chassis to the wheels as part of the suspension. Therefore, they have a significant influence on the driving characteristics of the vehicle. A dynamic or a comfortable driving style? The control arms are individually adjusted to the vehicle depending on the desired characteristics. They also absorb lateral movements and forces resulting from driving off and braking. Picture(A) A defective control arm can manifest in the following ways: (1).Noise (squeaking, creaking, rumbling). (2).Deteriorating driveability. (3).Increasingly woolly and imprecise steering. (4).Uneven tyre wear. Tip:If the control arm is in working order, it is possible to only replace the defective bearings and joints. However, replacing bearings, control arm bushings and ball joints can be very complex and costly. Picture(B) 1.First lift the vehicle using a car lift, ideally a wheel-free four-post car lift. This makes it easier to correctly tighten the control arm fixing screws. WARNING:Depending on the axle design, the control arm may need to be secured against falling with a suitable device, e.g. a transmission lifter. 2.Treat the fixing screws and nuts of the control arm with rust solvent and leave it to work for a few minutes so that they are easier to loosen. 3.On vehicles with automatic headlight levelling, it may be necessary to detach the leveling sensor from the control arm. Picture(C) 4.If the stabilizer is connected to the control arm, the next step is to loosen and remove the corresponding stabiliser fixing screws. 5.Loosen and remove the control arm fixing screws. 6.Loosen the ball joint at the steering knuckle with a suitable special tool (e.g. a puller). 7.Remove the old control arm. Picture(D) 8.Clean the mounting flange of the ball joint pin on the steering knuckle with sandpaper and then with brake cleaner. Otherwise single rust particles can enter the new control arm joint via the ball pin, potentially leading to premature failure of the joint. Picture(E) 9.Fit the new control arm with the supplied accessories and attach new fixing screws and nuts. Picture(F) 10.Reattach the stabilizer and, if applicable, the leveling sensor for headlight leveling to the control arm. NOTE:Do not tighten the fixing screws and nuts in this step, otherwise the rubber mounts will twist when the suspension compresses. This would lead to undesired preloading onf the mounts. Picture(G) 11.Now lower the vehicle until the suspension is compressed. Depending on vehicle type, load or unload the vehicle until the required height published in the specific installation instruction is reached. This is where a wheel-free four-post car lift is advantageous, as the underside of the vehicle can still be easily accessed once lowered. 12.Tighten the fixing screws with the torque stipulated by the vehicle manufacturer. 13.Lower the vehicle all the way. 14.Measure the chassis and adjust if necessary. 15.Check and, if necessary, adjust the headlight settings on vehicles with automatic headlight leveling where the leveling sensor is attached to the control arm. 16.To conclude, test-drive the vehicle. Frequently Asked Questions (1).What’s the function of control arm? The control arm connects the hub and the frame of the car. There are ball joints on the hub side and bushings on the frame side to achieve up and down instead of forward and rearward. (2).What is the significance of the control arm for the car? As an important part of the car suspension, the control arm is used to transmit the required supporting force of the wheel and to withstand all the front and rear direction stresses. It is an important safety part of the chassis system. Therefore, it requires high strength and reliability in the design. Its fatigue strength is directly related to the safety of vehicles and members. (3).How to tell the quality of control arm? Look at the materials and processing of the control arm: the materials used to control the arm, common are steel and aluminum alloy. In ordinary family cars, steel control arms are very common, and the basic appeal is to meet the strength while controlling costs. In the middle and high-end models, you will see the control arm of the aluminum alloy and the wheel bearing housing. In addition to meeting the strength of the suspension, this material can further reduce the weight and reduce the weight of the suspension spring to improve the suspension response. Improve driving performance. Look at chassis protection and workmanship: Regarding chassis protection, we mainly pay attention to whether it is equipped with engine under guard, whether there is coating or cover at the bottom of the car body, whether the oil pipe is covered with a guard plate, whether the front and rear wheel arches are protected. Board or coating coverage, etc. (4).Do I need to replace the control arm if the bushings are worn? What is the safety risk? Because the weight of the car is transferred through the control arm two rubber bushings are fitted at the pivot point and bolted to the frame. Road conditions and driving habits can contribute to the wear of these bushings which will become worn and fall apart. These bushing can be inspected by raising the car up and looking for an irregular configuration of the rubber center of the bushing. Many control arms have the ball joint manufactured into the arm which will be replaced along with the control arm itself. When one control arm is worn it is highly advised to replace the opposing arm. (5).What is the average cost of replacing control arms? The cost to replace control arms depend on the vehicle. Control arms cost different amounts depending on the vehicle, as well as the labor to install. Some are easy to install and take little time, while others can take several hours. Item Specifics Placement on Vehicle Front Type Control Arm & Ball Joint Assembly Universal Fitment No Control Arm Construction Forged Items Included Mounting Hardware Custom Bundle Yes Interchange Part Number K80397 K80398 K80104 OE/OEM Part Number Suspension Control Arms and Ball Joints Assembly,Sway Bars Ends Superseded Part Number Front Driver and Passenger Side Replacement Manufacturer Warranty 10 Year Brand ECCPP Manufacturer Part Number E81065502CP Adjustable Yes Greasable or Sealed Greasable Kit Included Surface Finish Premium Quality Kit Included 4 Pieces Cross Reference Part Number 2004 2003 2002 2001 Cross Part Number For Ford Escape Mazda Tribute Partlink Number Control Arm and Ball Joint Assembly Stabilizer Bar Link Fitment for left & right side, stabilizer sway bar end links, ball joints Fitment 2 For 2.0L, 3.0L, Limited, XLS, XLT, DX, ES, LX Fitment 3 For Escape Tribute Ford Mazda Fitment 4 Control Arm with Ball Joint Sway Bar Link Bundle Description Control Arm and Ball Joint Assembly,Sway Bar Features Greasable Finish Coated Cotter Pin Hole Yes Material Alloy Steel Mounting Style Bolt-On Item Specifics Placement on Vehicle Front Type Control Arm & Ball Joint Assembly Universal Fitment No Control Arm Construction Forged Items Included Mounting Hardware Custom Bundle Yes Interchange Part Number K80397 K80398 K80104 OE/OEM Part Number Suspension Control Arms and Ball Joints Assembly,Sway Bars Ends Superseded Part Number Front Driver and Passenger Side Replacement Manufacturer Warranty 10 Year Brand ECCPP Manufacturer Part Number E81065502CP Adjustable Yes Greasable or Sealed Greasable Kit Included Surface Finish Premium Quality Kit Included 4 Pieces Cross Reference Part Number 2004 2003 2002 2001 Cross Part Number For Ford Escape Mazda Tribute Partlink Number Control Arm and Ball Joint Assembly Stabilizer Bar Link Fitment for left & right side, stabilizer sway bar end links, ball joints Fitment 2 For 2.0L, 3.0L, Limited, XLS, XLT, DX, ES, LX Fitment 3 For Escape Tribute Ford Mazda Fitment 4 Control Arm with Ball Joint Sway Bar Link Bundle Description Control Arm and Ball Joint Assembly,Sway Bar Features Greasable Finish Coated Cotter Pin Hole Yes Material Alloy Steel Mounting Style Bolt-On Discount Targeted Disounts Terms (1).Targeted Discount Terms only apply to auto parts purchased from ECCPPAUTOPARTS, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).If you have reached any targeted discount threshold(s), please contact our customer services after you received all your items. (3).Targeted Discount will be refunded from buyer’s payment, which means ECCPPAUTOPARTS won’t provide any extra targeted discounts if full refund is issued. Targeted Shipping Discount (4).Since our warehouse is located in Los Angeles, California, therefore you are qualified for extra 2% targeted shipping discount off the item sales if shipping address of your order is in California(CA), Washington(WA), Oregon(OR), Nevada(NV). If you have reached this targeted shipping discount threshold, please contact our customer services after you received all your items. Note: Item sales means your payment for the product(s) only, excluding shipping and handling charges, US internet sales taxes. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).ECCPPAUTOPARTS has the final power of interpretation of all the above Targeted Discount Terms and Procedures. Shipping WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm. (1).Warehouse is located in Los Angeles, California, where local pickup transaction is temporarily not available. (2).Shipping services only cover 48 states and Washington DC in US Continental, while most of the time Alaska, Hawaii, Puerto Rico, American Samoa, U.S. Virgin Islands, Northern Marianas, Guam are not deliverable. (3).USPS PO Box, APO Army Post Office, FPO Fleet Post Office addresses are not available. (4).Global Shipping Program is temporarily not available due to the reason for package dimensions. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Your auto parts sometimes might be shipped with two or more separated packages due to weight limitation, please keep patient with no Item Not Received claim or Return request filed until by all of your items are received. (7).Seller is required to purchase signature confirmation to be protected if a buyer reports an item not received or opens a payment dispute if the order has a total cost (including shipping costs and any taxes) of $750 or more. Warranty Items valued over $15 on eBay that include a warranty or service contract must contain additional details in seller’s listing description. 10 Year Warranty Terms and Procedures (1).The warranty terms only apply to the auto parts purchased from ECCPPAUTOPARTS, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).ECCPPAUTOPARTS carries no warranty responsibilities for any auto parts removing fees, installation fees, consulting fees, labor costs, towing charges, rental car reimbursements. (3).The stated 10 year warranty is limited to only one brand new replacement for each part purchased during 10 year warranty time period. (4).ECCPPAUTOPARTS promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise ECCPPAUTOPARTS has the right to refuse any replacement requests. (5).ECCPPAUTOPARTS promises free replacement due to quality defects or item not as described issues after 90 calendar days from the date when buyers receive their items in the situation when buyers promise to prepay 15% of the original item sales price as postage for replacement, otherwise ECCPPAUTOPARTS has the right to refuse any replacement requests. (6).ECCPPAUTOPARTS carries no warranty responsibilities for any replacement due to car accidents, drag racing, unprofessional replacement, road hazard, disassembly. (7).Anyone who attempts to execute 10 year warranty procedures must be the original purchaser of the item(s), otherwise 10 year warranty terms void immediately. (8).Anyone who attempts to execute 10 year warranty procedures must provide screenshot of his or her original eBay order details if required, including buyer user name, shipping address, item title, item id, final sales price. (9).ECCPPAUTOPARTS has the final power of interpretation of the above 10 Year Warranty Terms and Procedures. Return (1).Most of items support 60 Days Money Back Guarantee. (2).Refunds will be credited within 2 or 3 business days after returned item(s) is received. Best Sales Pair For 2007-2014 Chevy Silverado Sierra Towing Power Heated LED Signal Mirrors USD 124.69 Front Wheel Hub Bearing For Chevy Monte Carlo Impala Cadillac Eldorado DTS FWD USD 40.38 Universal 12V Low Pressure 5-9 PSI Electric Fuel Pump Installation Kit E8012S USD 14.15 Pair Manual Adjust Tow Mirrors For 1988-1998 Chevy GMC C K 1500/2500/3500 USD 62.99 ECCPP 2 Pcs Wheel Hub Bearing Front For Buick LaCrosse Century Regal Lesabre FWD USD 60.95 Newly Listed For Chevy S10 1998-04 Silverado 1500 99-2002 Transfer Case Shift Motor Actuator USD 74.29 Spoiler Wing Fit For 2013-2016 Audi A4 B8.5 Sedan Models USD 110.85 Spoiler Wing For BMW F30 3 Series F35 2011 2012 2013 2014 2015 2016 2017 2018 USD 118.85 V Style Spoiler Wing Fit For Audi A3 S3 RS3 2015-2018 Sedan USD 110.85 Spoiler Wing For 2008-2013 INFINITI G37 COUPE / 2014-2015 Q60 USD 120.85 4PCS Front Lower Control Arm Stabilizer Sway Bar Link For 2001-2004 Ford Escape Introduction: Our store provide varieties of High Quality Suspension Products, if this iterm can not meet your needs, you can entry our store to find the products you need. Before you place the order, please check the compatibility and the view Notes or contact us, make sure it fits your vehicle. we hope you enjoy your shopping. Fit for 2001 – 2004 FORD ESCAPE All Models 2001 – 2004 MAZDA TRIBUTE All Models Package Includes: 1x Front Lower (Passenger Side) Control Arm Assembly – K80397 1x Front Lower (Driver Side) Control Arm Assembly – K80398 2x Stabilizer / Sway Bar End Link – K80104 10 Year Warranty Please check above compatibility list to make sure it fits your vehicle. Note: Some of the parts we have grease fittings and other parts come factory sealed, you may receive one of the parts.but don’t worry, this does not affect the performance or quality of the parts. Suspension Control Arm Some lateral multilink front suspensions have compression and lateral lower arms. The lateral arm prevents front wheel movement, and the compression arm prevents fore-and-aft front wheel movement. A rubber insulating bushing in the inner end of the lateral arm is bolted to the chassis. A second rubber insulating bushing near the outer end of the lateral arm is bolted to the damper fork. The upper end of the damper fork is bolted to the front strut. A ball joint in the outer end of the lateral arm is bolted into the steering knuckle. A rubber insulating bushing in the inner end of the compression arm is bolted to the chassis, and a ball joint in the outer end of this arm is bolted into the steering knuckle. The upper control arm is mounted higher so it is above the front tire. The higher upper control arm and the lateral and compression lower arms provide excellent suspension stability and steering control, especially during high-speed cornering or when driving on irregular road surfaces. A ball joint in the outer end of the upper control arm is attached to the top of the knuckle, and two shafts in the inner end of this arm are bolted into the strut tower. There are no provisions for camber or caster adjustments on this multilink front suspension. Suspension Control Arm Replacement Guideline: Control arms are installed in pairs on the front and rear axle and connect the chassis to the wheels as part of the suspension. Therefore, they have a significant influence on the driving characteristics of the vehicle. A dynamic or a comfortable driving style? The control arms are individually adjusted to the vehicle depending on the desired characteristics. They also absorb lateral movements and forces resulting from driving off and braking. Picture(A) A defective control arm can manifest in the following ways: (1).Noise (squeaking, creaking, rumbling). (2).Deteriorating driveability. (3).Increasingly woolly and imprecise steering. (4).Uneven tyre wear. Tip:If the control arm is in working order, it is possible to only replace the defective bearings and joints. However, replacing bearings, control arm bushings and ball joints can be very complex and costly. Picture(B) 1.First lift the vehicle using a car lift, ideally a wheel-free four-post car lift. This makes it easier to correctly tighten the control arm fixing screws. WARNING:Depending on the axle design, the control arm may need to be secured against falling with a suitable device, e.g. a transmission lifter. 2.Treat the fixing screws and nuts of the control arm with rust solvent and leave it to work for a few minutes so that they are easier to loosen. 3.On vehicles with automatic headlight levelling, it may be necessary to detach the leveling sensor from the control arm. Picture(C) 4.If the stabilizer is connected to the control arm, the next step is to loosen and remove the corresponding stabiliser fixing screws. 5.Loosen and remove the control arm fixing screws. 6.Loosen the ball joint at the steering knuckle with a suitable special tool (e.g. a puller). 7.Remove the old control arm. Picture(D) 8.Clean the mounting flange of the ball joint pin on the steering knuckle with sandpaper and then with brake cleaner. Otherwise single rust particles can enter the new control arm joint via the ball pin, potentially leading to premature failure of the joint. Picture(E) 9.Fit the new control arm with the supplied accessories and attach new fixing screws and nuts. Picture(F) 10.Reattach the stabilizer and, if applicable, the leveling sensor for headlight leveling to the control arm. NOTE:Do not tighten the fixing screws and nuts in this step, otherwise the rubber mounts will twist when the suspension compresses. This would lead to undesired preloading onf the mounts. Picture(G) 11.Now lower the vehicle until the suspension is compressed. Depending on vehicle type, load or unload the vehicle until the required height published in the specific installation instruction is reached. This is where a wheel-free four-post car lift is advantageous, as the underside of the vehicle can still be easily accessed once lowered. 12.Tighten the fixing screws with the torque stipulated by the vehicle manufacturer. 13.Lower the vehicle all the way. 14.Measure the chassis and adjust if necessary. 15.Check and, if necessary, adjust the headlight settings on vehicles with automatic headlight leveling where the leveling sensor is attached to the control arm. 16.To conclude, test-drive the vehicle. Frequently Asked Questions (1).What’s the function of control arm? The control arm connects the hub and the frame of the car. There are ball joints on the hub side and bushings on the frame side to achieve up and down instead of forward and rearward. (2).What is the significance of the control arm for the car? As an important part of the car suspension, the control arm is used to transmit the required supporting force of the wheel and to withstand all the front and rear direction stresses. It is an important safety part of the chassis system. Therefore, it requires high strength and reliability in the design. Its fatigue strength is directly related to the safety of vehicles and members. (3).How to tell the quality of control arm? Look at the materials and processing of the control arm: the materials used to control the arm, common are steel and aluminum alloy. In ordinary family cars, steel control arms are very common, and the basic appeal is to meet the strength while controlling costs. In the middle and high-end models, you will see the control arm of the aluminum alloy and the wheel bearing housing. In addition to meeting the strength of the suspension, this material can further reduce the weight and reduce the weight of the suspension spring to improve the suspension response. Improve driving performance. Look at chassis protection and workmanship: Regarding chassis protection, we mainly pay attention to whether it is equipped with engine under guard, whether there is coating or cover at the bottom of the car body, whether the oil pipe is covered with a guard plate, whether the front and rear wheel arches are protected. Board or coating coverage, etc. (4).Do I need to replace the control arm if the bushings are worn? What is the safety risk? Because the weight of the car is transferred through the control arm two rubber bushings are fitted at the pivot point and bolted to the frame. Road conditions and driving habits can contribute to the wear of these bushings which will become worn and fall apart. These bushing can be inspected by raising the car up and looking for an irregular configuration of the rubber center of the bushing. Many control arms have the ball joint manufactured into the arm which will be replaced along with the control arm itself. When one control arm is worn it is highly advised to replace the opposing arm. (5).What is the average cost of replacing control arms? The cost to replace control arms depend on the vehicle. Control arms cost different amounts depending on the vehicle, as well as the labor to install. Some are easy to install and take little time, while others can take several hours. Item Specifics Placement on Vehicle : Front Type : Control Arm & Ball Joint Assembly Universal Fitment : No Control Arm Construction : Forged Items Included : Mounting Hardware Custom Bundle : Yes Interchange Part Number : K80397 K80398 K80104 OE/OEM Part Number : Suspension Control Arms and Ball Joints Assembly,Sway Bars Ends Superseded Part Number : Front Driver and Passenger Side Replacement Manufacturer Warranty : 10 Year Brand : ECCPP Manufacturer Part Number : E81065502CP Adjustable : Yes Greasable or Sealed : Greasable Kit Included : Surface Finish : Premium Quality Kit Included : 4 Pieces Cross Reference Part Number : 2004 2003 2002 2001 Cross Part Number : For Ford Escape Mazda Tribute Partlink Number : Control Arm and Ball Joint Assembly Stabilizer Bar Link Fitment : for left & right side, stabilizer sway bar end links, ball joints Fitment 2 : For 2.0L, 3.0L, Limited, XLS, XLT, DX, ES, LX Fitment 3 : For Escape Tribute Ford Mazda Fitment 4 : Control Arm with Ball Joint Sway Bar Link Bundle Description : Control Arm and Ball Joint Assembly,Sway Bar Features : Greasable Finish : Coated Cotter Pin Hole : Yes Material : Alloy Steel Mounting Style : Bolt-On Item Specifics Placement on Vehicle Front Type Control Arm & Ball Joint Assembly Universal Fitment No Control Arm Construction Forged Items Included Mounting Hardware Custom Bundle Yes Interchange Part Number K80397 K80398 K80104 OE/OEM Part Number Suspension Control Arms and Ball Joints Assembly,Sway Bars Ends Superseded Part Number Front Driver and Passenger Side Replacement Manufacturer Warranty 10 Year Brand ECCPP Manufacturer Part Number E81065502CP Adjustable Yes Greasable or Sealed Greasable Kit Included Surface Finish Premium Quality Kit Included 4 Pieces Cross Reference Part Number 2004 2003 2002 2001 Cross Part Number For Ford Escape Mazda Tribute Partlink Number Control Arm and Ball Joint Assembly Stabilizer Bar Link Fitment for left & right side, stabilizer sway bar end links, ball joints Fitment 2 For 2.0L, 3.0L, Limited, XLS, XLT, DX, ES, LX Fitment 3 For Escape Tribute Ford Mazda Fitment 4 Control Arm with Ball Joint Sway Bar Link Bundle Description Control Arm and Ball Joint Assembly,Sway Bar Features Greasable Finish Coated Cotter Pin Hole Yes Material Alloy Steel Mounting Style Bolt-On DiscountShippingWarrantyReturnFeedback Targeted Disounts Terms (1).Targeted Discount Terms only apply to auto parts purchased from ECCPPAUTOPARTS, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).If you have reached any targeted discount threshold(s), please contact our customer services after you received all your items. (3).Targeted Discount will be refunded from buyer’s payment, which means ECCPPAUTOPARTS won’t provide any extra targeted discounts if full refund is issued. Targeted Shipping Discount (4).Since our warehouse is located in Los Angeles, California, therefore you are qualified for extra 2% targeted shipping discount off the item sales if shipping address of your order is in California(CA), Washington(WA), Oregon(OR), Nevada(NV). If you have reached this targeted shipping discount threshold, please contact our customer services after you received all your items. Note: Item sales means your payment for the product(s) only, excluding shipping and handling charges, US internet sales taxes. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).ECCPPAUTOPARTS has the final power of interpretation of all the above Targeted Discount Terms and Procedures. WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm. (1).Warehouse is located in Los Angeles, California, where local pickup transaction is temporarily not available. (2).Shipping services only cover 48 states and Washington DC in US Continental, while most of the time Alaska, Hawaii, Puerto Rico, American Samoa, U.S. Virgin Islands, Northern Marianas, Guam are not deliverable. (3).USPS PO Box, APO Army Post Office, FPO Fleet Post Office addresses are not available. (4).Global Shipping Program is temporarily not available due to the reason for package dimensions. (5).We usually need a 1-2 business day as handling time for packaging and shipping scheduling. Estimated delivery dates should be 4-6 business days after your payment is received. (6).Your auto parts sometimes might be shipped with two or more separated packages due to weight limitation, please keep patient with no Item Not Received claim or Return request filed until by all of your items are received. (7).Seller is required to purchase signature confirmation to be protected if a buyer reports an item not received or opens a payment dispute if the order has a total cost (including shipping costs and any taxes) of $750 or more. Items valued over $15 on eBay that include a warranty or service contract must contain additional details in seller’s listing description. 10 Year Warranty Terms and Procedures (1).The warranty terms only apply to the auto parts purchased from ECCPPAUTOPARTS, which only includes suspension kit, control arm, tie rod end, ball joint, sway bar, stabilizer link, pitman arm, idler arm, steering center link. (2).ECCPPAUTOPARTS carries no warranty responsibilities for any auto parts removing fees, installation fees, consulting fees, labor costs, towing charges, rental car reimbursements. (3).The stated 10 year warranty is limited to only one brand new replacement for each part purchased during 10 year warranty time period. (4).ECCPPAUTOPARTS promises free replacement due to quality defects or item not as described issues within 90 calendar days from the date when buyers receive their items in the situation when buyers are willing to provide convictive proofs or professional diagnose report if required, otherwise ECCPPAUTOPARTS has the right to refuse any replacement requests. (5).ECCPPAUTOPARTS promises free replacement due to quality defects or item not as described issues after 90 calendar days from the date when buyers receive their items in the situation when buyers promise to prepay 15% of the original item sales price as postage for replacement, otherwise ECCPPAUTOPARTS has the right to refuse any replacement requests. (6).ECCPPAUTOPARTS carries no warranty responsibilities for any replacement due to car accidents, drag racing, unprofessional replacement, road hazard, disassembly. (7).Anyone who attempts to execute 10 year warranty procedures must be the original purchaser of the item(s), otherwise 10 year warranty terms void immediately. (8).Anyone who attempts to execute 10 year warranty procedures must provide screenshot of his or her original eBay order details if required, including buyer user name, shipping address, item title, item id, final sales price. (9).ECCPPAUTOPARTS has the final power of interpretation of the above 10 Year Warranty Terms and Procedures. (1).Most of items support 60 Days Money Back Guarantee. (2).Refunds will be credited within 2 or 3 business days after returned item(s) is received. Copyright of ECCPP. All rights reserved.
Frequently Asked Questions About 4PCS Front Lower Control Arm Stabilizer Sway Bar Link For 2001-2004 Ford Escape in My Website
quediade.com is the best online shopping platform where you can buy 4PCS Front Lower Control Arm Stabilizer Sway Bar Link For 2001-2004 Ford Escape from renowned brand(s). quediade.com delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.
What are the best-selling 4PCS Front Lower Control Arm Stabilizer Sway Bar Link For 2001-2004 Ford Escape on quediade.com?
quediade.com helps you to shop online and delivers Rayban to your doorstep. The best-selling Rayban on quediade.com are: Ray Ban 601/9A Black WRAP Gray Polarized Sunglasses Italy Ray Ban RB 4181 Polarized Sunglasses, 710/83 Havana / Brown (BAD LENSES) #G06 RAY BAN RB8313 001 51 Gold Arista Men’s 58 mm Sunglasses Brand New Sealed Ray-Ban RB 4440-N-F Blaze Wayfarer in Blue Violet Gradient Lens NEW Ray Ban Polished Black POLARIZED Gray Green Lens Sunglass RB 3516 006/9A Ray Ban Sunglasses Classic Wayfarer RB2151 Brown Made In Italy NEW* Ray Ban AVIATOR SILVER 64mm w Brown Purple Gradient Sunglass RB 3387 003 Ray-Ban Sunglasses RB3023 Highstreet MSW W3132 Brown Oval Frames Only 55[]00 3N RAY BAN RB3016 133751 Pink Havana Unisex 49 mm Sunglasses Ray-Ban RB2132 New Wayfarer Square Polarized Sunglasses Black With Divots Ray-Ban Sunglasses RB3025 Aviator Classic Gold Frame Polarized Brown Lens 58mm Ray-Ban Gatsby I RB4256 Round Sunglasses 6092/55 Havana Brown Blue Mirror Lens Ray Ban Italy RB4640 601/31 50[]20 Black Sunglasses “ READ” Sunglasses Ray Ban AVIATOR; Light GRAY GRADIENT Lens: RB3025; Size 58 standard Ray-Ban Wayfarer Black On Yellow /Light Gray Lens Discounted Model 2140 1000/32 RAY BAN RB3721CH 9144A1 Black Blue Mirror Polarized Men’s 59 mm Sunglasses Ray Ban Polarized Sunglasses Only Worn Once used rb3721ch RAY BAN RB3016F W0366 Tortoise on Arista Square 55 mm Unisex Sunglasses RAY BAN RB3016 114517 Sand Havana on Arista Square 51 mm Unisex Sunglasses Ray Ban RB 4078 642 Brown Striped Rectangle Sunglasses Frames Italy Designer Ray-Ban Titanium Chromance RB8062 Sunglasses Arista Gold w/ Polarized Blue Ray-Ban Caribbean Sunglasses Striped Grey w/ Dark Grey Lenses RB2248 Ray-Ban New Wayfarer Matte Black Rubber l Green G-15XLT RB2132 622 58mm Ray-Ban Boyfriend Reverse Sunglasses RB R0501S Polished Black Green Tint w/case Ray Ban Sunglasses Frames RB3293 004/9A 67-13 3P Nice RAY BAN RBR0502S 6707GR Transparent Dark Grey Unisex 53 mm Sunglasses RAY-BAN RB3273 Mens Aviator Sunglasses Polarized Lenses Clamshell Hard Case Ray Ban RB 4184 Black Sunglasses Ray-Ban AVIATOR RB3025 112/4L MATTE GOLD W/ 58-14 58mm BLUE MIRROR POLARIZED D78 Ray-Ban RB 4057 601 3N Sunglasses Mens Black Full Frame 15156 RAY BAN RB4165 651287 Transparent Dark Grey Men’s 55 mm Sunglasses Ray-ban RB4331 601 S 80 Black Mens Rectangle Sunglasses 59-17 3N “ READ” RAY BAN RB2132 865 B1 Rubber Havana Dark Grey Unisex 58 mm Sunglasses RAY BAN RB3016F W0365 Black on Arista Square 55 mm Unisex Sunglasses New Ray-Ban Round Gray Gunmetal Green Mirror Sunglasses RB4243 6262B4 49 $153 Ray-Ban Gatsby II RB4257 Round Sunglasses 601/71 Black Gold Frame Green Lens 50 [RB4188-600/783_63] Mens Ray-Ban Rectangle Polarized Sunglasses Ray-Ban RB3527 Sunglasses 029/9A Matte Gunmetal Frame Green Polarized Lens 61mm Sunglasses Ray Ban CLUBMASTER RB3016 / SILVER MIRRORED Lens / Standard Size Ray-Ban RB4171 Black Matte/ Mirrored Erika Sunglasses RAY-BAN Sunglasses RB4162 601/32 Polished Black/Gray Aviator NEW Italy RAY-BAN RB3387 POLARIZED Sunglasses 002/9A Black/Green Gray NEW Aviator 🔥 Ray-Ban RB3549 POLARIZED Sunglasses | 006/9A – Black / Classic G-15 Lens $188 Vintage RAY BAN B&L Sunglasses PREDATOR CATS Black Plastic Frame Ray-Ban RB3717 002/B1 57-18, Polished Black Frame, Dark Grey Lens, NEW! RAY BAN RB 8301 Aviator Sunglasses 61 14 140 Made In Italy Ray Ban Justin Rb4165 622/T3 Black Rubber Matte Sunglasses Frame Only RAY-BAN CATS 4000 SUNGLASSES LIGHT HAVANA / CRYSTAL BROWN GRADIENT RB4128 710/51 Open Box Ray-Ban 0RB4428 Sunglasses, Havana Frame, Blue Lens RAY BAN RB2210 901 58 Black Green Polarized Unisex 53 mm Sunglasses Ray-Ban RB3576N 043/71 Blaze Polished Gold Frame With Dark Green Lenses Ray-Ban New Aviator Sunglasses RB 3625 002/B1 Polished Black Metal 62mm w/case Ray Ban Sunglasses Blaze Shooter RB3581N 1537V Demi gloss Black 32mm Blue Lens Ray Ban RB3447 001 ROUND METAL Gold/ Green Classic G-15 AUTHENTIC ITALY Ray-Ban RB2027 Black l Polarized Mirror Grey RB2027 601/W1 62mm Ray-Ban Wayfarer Folding Classic RB4105 601 50 Ray-Ban Original Wayfarer Style Classic Sunglasses – Black 2140 Aftermarket Silicone RayBan Replacement Temple (Arm) Tips BROWN 3217 Ray Ban Ray Ban RB R0101S Ray-Ban Aviator Reverse 001/VR 62011 145 3N Italy Ray-Ban Aviator Classic Gold Framed Sunglasses Great Used Condition Ray-Ban Sunglasses RB4395 Kiliane 667771 Black green Man Woman [RB3293-001/13_63] Mens Ray-Ban Aviator Sunglasses Ray-Ban Boyfriend Reverse Brown Transparent Sunglasses RBR0501S 6709CB 56 Ray Ban Sunglasses Frames RB 4107 601/58 Rectangle Black Sunglasses Italy 3P RAY BAN Clubround Classic Sunglasses 51-19 Tortoise Black Unisex w Case Ray Ban RB3447 112/Z2 ROUND FLASH LENSES Copper Flash lenses; Gold AUTHENTIC NEW Men’s Ray-Ban Sunglasses RB4331 710/73 Havana brown, FREE SHIPPING Ray-Ban Sunglasses RB 3254 Pilot Black Full-Rim With Case Frames Only New Ray Ban Sunglasses 3016 W0365 Clubmaster Black and Gold G-15 Lens 51mm Ray Ban RB2447 1159/4E Round Fleck Black Havena Unisex Italy W/ Case Rayban RB3588 55 19 140 Sunglasses 9014/80 3N READ DESCRIPTION Ray Ban RB4089 Balorama Sunglasses Polarized Ray Ban rb3162 006 Sleek Black Metal Sunglasses Frame Only 52-19 NO LENSES Ray-Ban Sunglasses RB3016 Clubmaster Classic Black Frame Green Lens 49mm Unisex Ray-Ban RB3664CH Chromance Square Sunglasses Light Brown w/ Brown Rayban Mens Sunglasses RB4184 Black Gray Ray-Ban Sunglasses RB 4194 601-53-17 Unisex Black Plastic Frames Ray-Ban Olympian Aviator Sunglasses Gray Gradient Havana Green Lens Case Cloth Ray-Ban Sunglasses Junior RJ9548SN Ray-Bans Black New Wayfarar Polarized Sunglasses 😎 Ray Ban RB3198 014/83 Sleek Brown Wrap Polarized Sunglasses 55-18 Read RAY-BAN RB 4387 601/71 BLACK AUTHENTIC FRAMES SUNGLASSES 56-18 Rayban RB3689 Aviator Sunglasses 001/GE Gold Frame Blue To Peach Gradient 62mm Ray-Ban Mega Wayfarer Sunglasses RB 0840S Polished Transparent Dark Gray w/case Ray-Ban Sunglasses RB4416 NEW CLUBMASTER 601/31 Black Gold Frames G-15 Lenses Ray-Ban RB 3364 014 Brown / Tortoise Wrap Sunglasses 59[]17 MADE IN ITALY Ray-Ban RB3025 019/W3 Aviator Sunglasses Matte Silver / Polarized Silver Mirror Aftermarket Silicone RayBan Replacement Temple/Arm Tips RB 3506 BROWN Ray Ban Ray-Ban RB 3490 Brown Copper Sunglasses Dark Brown Lens 62-16-140 Italy Eyewear Ray Ban RB3025 AVIATOR 58mm Blue Flash POLARIZED/Silver AUTHENTIC ITALY Ray-Ban Aviator Reverse Gold Frame, Green Lens Sunglasses RBR0101S 001/82 59 Pre-Owned Ray-Ban RB3447 112/17 Round Metal Gold Frame / Blue Mirrored Lenses Ray-Ban RB3025 002/58 Black Aviator Green Classic Polarized 58mm Sunglasses Ray Ban Italy RB 4285 710/14 55-20-140 3N Tortoise/Brown Sunglasses Frame UY81 Men’s Rayban Sunglasses | Used Condition Dark Blue Made In Italy RAY BAN ANDREA BLACK SUNGLASSES WITH DARK BLUE LENSES AVIATION RB3595 901480 Ray-Ban RB3119 001 Olympian Gold/Green G15 Men’s Sport Sunglasses Sizes 59 & 62 Ray-Ban Boyfriend Light Grey Lens Black Frame Unisex Sunglasses RB4147 601/32-60 Ray-Ban Classic Aviators RB3025 Total Silver Sunglasses (Open Box, Never Used) Sunglasses 2132 Ray Ban NEW WAYFARER / CLASSIC Lens / Standard Size Mens Pullover Fleece Hoodie